
Config 2018-09-25-a
-------------
* New inputs for LTU Vertical Dechirper 
  downstream mirror 
    MIRR_LTU1_548_OUT_LIMSW
    MIRR_LTU1_548_IN_LIMSW

Config 2018-03-02-a
-------------
* Remove MFX_LENS_1_SAFE

Config 2017-12-13-a
-------------
* Change all PIC/BLM loss and test inputs to be non-autorecoverable
  (latching). Most already had this setting, but a small
  number had been misconfigured. 
* Delete all rate-based PIC/BLM loss inputs. These were
  intended for rate-recovery, whose prospects are currently
  unknown and these input state changes flood the log.

Config 2017-10-17-a
-------------
* Add A-line secondary target IN/OUT status

Config 2017-07-24-a
-------------
* New input XCS:PBT:VGC_OUT_SUM

Config 2017-06-19-a
-------------
* Swap XLEAP mirror 3mm and 5mm position
  inputs (they are currently reversed).


Config 2017-06-08-a
-------------
* New inputs for XLEAP wiggler gap
  and insertable devices


Config 2017-05-24-a
-------------
* Remove obsolete inputs:
    THZR_DMP1_350_OUT_LIMIT
    THZR_DMP1_350_IN_LIMIT

Config 2017-05-22-a
-------------
* Add inputs for XLEAP LTU Beam Loss Fiber

Config 2017-05-13-a
-------------
* Remove OTR22 inputs:
    OTRS_LI25_342_OUT_LMTSW
    OTRS_LI25_342_IN_LMTSW
* For 2017 FEE reconfiguration, many changes.
    See changes.log and supporting files for details.


Config 2017-05-10-b
-------------
* New A-line valve VVPG_BSYA_340_OPEN_LIMSW
* Remove long-obsolete devices:
   DEV_52SL1
   DEV_50B1
   DEV_50PR3OUT
   HVPS_BSY0_54_POWER  
* Remove inputs not needed for BSY Reconfiguration:
   TRGT_BSYA_960_OUT_LIMSW
   TRGT_BSYA_960_IN_LIMSW
   TRGT_BSYA_960_FLOW_SW
   TRGT_BSYA_960_KLIXON
   COLL_BSYH_479_FLOW_SW
   COLL_BSYH_487_FLOW_SW
   COLL_BSYH_495_FLOW_SW
   COLL_BSYH_520_FLOW_SW

Config 2017-04-28-a
-------------
* Replace individual PCAPM flow switches
  with single switch for PCAPM1-4
* Changed PIC channel assignments for
  PCAPM1-4 PICs
* Remove unused constantly cycling PIC inputs
  for new BSYH PICs. Note will need
  to be re-added to implement rate recovery!

Config 2017-04-17-a
-------------
Many changes to support 2017 downtime BSY Reconfiguration of LCLS common-line,
including some A-line related changes. See changes.log and the other supporting
documents for details. 


Config 2016-10-19-a
-------------
* Delete obsolete device inputs:
  Dump B4C
  BSY PR45
  BSY PR55

Config 2016-10-17-a
-------------
* Add new MFX inputs. 
  See changes.log and *diff*.html files for details

Config 2016-08-25-a
-------------
* Add new Analog Link Node 44 and first set of inputs
  See changes.log for details

Config 2016-05-02-a
-------------
* Remove unused and obsolete device
   TIUKEYSW aka TIU:IN20:1:KEY_SWITCH_STATE


Config 2016-04-26-a
-------------
* Delete obsolete dechirper devices
   DCHP_LTU1_545_WDOG_SUM
   DCHP_LTU1_545_BPM_INTOL

* New devices for FEE spectrometer crystal protection 
  XTAL_FEE1_441_PULSEENERGY, LN10, Card 4, Ch 3
  GDET_FEE1_1_CAL_OK, LN10 Card 4, Ch 4
Config 2016-04-24-a
-------------
* No config changes. Modify Makfile.conf to use scripts/version1-0-6

Config 2016-01-22-a
-------------
* Rename some input names to match their PV names. 
  See changes.log for details.

Config 2015-12-07-b
-------------
* Removed unused PV attributes from database.
  For some External PV objects, fill in missing Device Details
  fields. See changes.log for details.

Config 2015-12-07-a
-------------
* Removed unused devicedetails and fault objects from database:

Devicedetails:
THZR LTU1 741 IN_LIMSW
MIRR FEE1 1560 OUT_LIMIT1 (two of these)
MIRR FEE1 1560 OUT_LIMIT2 (two of these)
XTAL FEE1 441 OUT_LIMSW

Faults:
'SPARE'
'02B'
'02A'
'Valve is open'
'A-line Kicker Pulser1': PULSER1_ON, PULSER1_OFF, PULSER1_TRIG_ENB, PULSER1_TRIG_LOCK
'A-line Kicker Pulser2': PULSER2_ON, PULSER2_OFF, PULSER2_TRIG_ENB, PULSER2_TRIG_LOCK
'SL10 CLOSED'
'ST22 OUT'
'THZ-2 Foil Out Switch'
'THZ-2 Foil In Switch'
'FEE spectrometer crystal OUT'

Config 2015-12-01-a
-------------
* Removed duplicate device instances:
  MIRR_FEE1_1560_OUT_LIMIT1 (2 duplicates)
  MIRR_FEE1_1560_OUT_LIMIT2 (2 duplicates)
  XTAL_FEE1_441_OUT_LIMSW (1 duplicate)

Config 2015-11-30-a
-------------
* Remove duplicate PvArea LTU1 from database. 
  Changed all devices that used the deleted instance
  to use the other instance. See changes.log for list
  of affected devices.
* Remove duplicate PvDeviceType BFW from database. 
  Changed all devices that used the deleted instance
  to use the other instance. See changes.log for list
  of affected devices.

Config 2015-11-23-a
-------------
* Remove unused devices:
  FLOOD_SW_OK
  TARGET_EPV_FLOSW_2_OK
  AMO_HFP_MPA_02ASPARE
  MTLM_LOGIC_OK
  STOPPER_2_IN_OUT
  STOPPER_1_IN_OUT
  AMO_HFP_MPA_02BSPARE
  RAD_SHLD_FLOSW_9_OK

* Remove unused LN channels
  LN 40 Card 1 Channel 10
  LN 40 Card 1 Channel 11
  LN 40 Card 2 Channel 9
  LN 40 Card 2 Channel 10
  LN 40 Card 2 Channel 11
  LN 40 Card 3 Channel 11
  LN 42 Card 2 Channel 4
  LN 42 Card 2 Channel 6
  LN 42 Card 3 Channel 8

Config 2015-11-09-a
-------------
* Add MEC_DV4_VGC_01_OPN_DI
* Misc LN 39-41 rename and delete
  for photon-side inputs. Details
  in directory.

Config 2015-10-09-a
-------------
* Add MEC_DV4_VGC_01_OPN_DI

Config 2015-09-03-a
-------------
* Add Dechirper inputs:
    BLM:LTU1:BLF545:LOSS_60_L
    BLM:LTU1:BLF545:LOSS_60_H
    BLM:LTU1:BLF545:TEST_L   
    BLM:LTU1:BLF545:TEST_H   
    BLM:LTU1:BLF545:TEST_1_L
    BLM:LTU1:BLF545:TEST_1_H
    BLM:LTU1:BLF545:PED_L    
    BLM:LTU1:BLF545:PED_H
* Add new IN20 fast valve:
    VVFV:LI20:785:OPEN_LMTSW
* Add new MFX hutch vacuum valve PLC summary:
    MFX_MPS_PLC_VAC_OK

Config 2015-07-13-a
-------------
* Add Dechirper inputs:
    DCHP_LTU1_545_BPM_INTOL_THRESHOLD
    DCHP_LTU1_545_GAP_LIMSW_NEGZ_POSITION
    DCHP_LTU1_545_GAP_LIMSW_POSZ_POSITION
    DCHP_LTU1_545_OUT_LIMSW_NEGY_POSITION
    DCHP_LTU1_545_OUT_LIMSW_POSY_POSITION
    DCHP_LTU1_545_WDOG_SUM_STATE
    DCHP_LTU1_555_GAP_LIMSW_NEGZ_POSITION
    DCHP_LTU1_555_GAP_LIMSW_POSZ_POSITION
    DCHP_LTU1_555_OUT_LIMSW_NEGX_POSITION
    DCHP_LTU1_555_OUT_LIMSW_POSX_POSITION
    USEG_UND1_1_ALL_OUT_STATE
* Add new CXI gate valve open limit switch:
    CXI_SC3_VGC_01_OPN_DI_POSITION

Config 2015-05-18-a
-------------
* Add FEE Gas attenuator pressure threshold interlock
  to LN38: VMPS:FEE1:E202:NOGAS

Config 2015-05-01-a
-------------
* Add LTU Dechirper Beam Loss Fiber channel
  to LN30: BLM:LTU1:BLF545

Config 2015-04-22-a
-------------
* Add PIC LN 42 trigger input status, fault:
  PICM_BSYA_2061_NO_TRIG_MISSED

Config 2014-12-05-a
-------------
* Add fault
  XTAL_FEE1_441_ENERGY
* Rename
  XTAL_FEE1_442_OUT_LIMSW
  to
  XTAL_FEE1_441_OUT_LIMSW

Config 2014-11-25-a
-------------
* Add faults
  KICK:LTU0:320:ABORTWIN
  KICK:LTU0:320:STANDBYWIN
  
Config 2014-10-24-a
------------
* Add inputs
  XPP_SB2_VGC_02_OPN_DI_POSITION
  XPP_SB2_VGC_03_OPN_DI_POSITION

Config 2014-10-16-a
------------
* Add FEE Spectrometer Crystal OUT limit switch

Config 2014-07-02-a
------------
* Add missing BSY PIC HVPS inputs: 2-6
* Update input and state names for all PIC HVPS to
  be consistent

Config 2014-06-09-a
------------
* Added IN and OUT limit switches for DMP SP0 spoiler

Config 2014-02-28-a
------------
* Changed names and removed devices for CXI

Config 2014-02-06-a
------------
* Use databaseCommon/version1-0-4 to add channel acces
  security to MPS bypasses

Config 2013-10-15-a
------------
* Remove AMO_HFP_VGC_02A, AMO_HFP_VGC_02B
* Add AMO_LMP_VGC_30_OPN_DI, AMO_LMP_VGC_30_CLS_DI

Config 2013-10-10-a
------------
* Remove OTRS LTU1 743 OUT/IN LIMITs (PSI profile monitor)
* Add    YAGS LTU1 743 OUT/IN LIMITs (PSI profile monitor)

Config 2013-10-04-a
------------
* Add OTRS LTU1 743 OUT/IN LIMITs (PSI profile monitor)

Config 2013-09-24-a
------------
* Add BSY GLAST Target Flow Switch

Config 2013-08-28-a
------------
* Add A-line B1/B2 OFF status Chains A and B from PPS

Config 2013-08-02-a
------------
* Add SXRSS devices; remove obsolete e+ devices

Config 2013-07-08-a
------------
* Add 2 M1S Mirror Out Limit Switches
* Add M1S Mirror 'Energy OK' input 
  (repurpose unused LN11 'BC1_CID' input for this)

Config 2013-06-03-a
------------
* Add GLAST Target Limit Switches

Config 2012-11-12-a
------------
* Add THZR:LTU1:741:IN_LMTSW, OUT_LMSW limit switches for new THZ-2 
* removed a spare vacuum valve on LN 31, card 1, ch 9 so that we could add
  these limit switches

Config 2012-10-26-a
------------
* Add BEND:DMP1:400:INTOL_BMIN2 which is beam lower E limit of 
  3.3GeV if stoppers SH1 or S2 are not IN

Config 2012-10-15-a
------------
* Add BEND:DMP1:400:INTOL_BMIN which is beam lower E limit of 
  2.3GeV for the Undulator region

Config 2012-09-26-a 
------------
* copied from 2012-09-18-a (skipping 2012-09-15-a)
* add new SXR valve per Photon controls

Config 2012-09-25-a DO NOT USE THIS VERSION
------------
* add new SXR valve per Photon controls
* add new PICMs 380, 381 for XTCAV in DMP1

Config 2012-09-18-a
------------
* add new NEH XPP SH3 stopper status per Photon controls
* add new vacuum valve in DMP at 355 (XTCAV)

Config 2012-08-08-a
------------
* build for epics-3-14-12


Config 2012-06-25-a
------------
* Added BSYA PPS Inputs



Config 2012-06-05-a
------------
* Clean up names of A-Line devices, desc was too long
	
DESC, "SLIT_BSYA_2010_SL10_CLS_LIMIT" to  blahÉLIM instead of LIMIT 
DESC, "STPR_BSYA_2275_ST22_OUT_LIMIT" to  blahÉLIM

* Remove recovery for A-Line Kicker Rate Inputs so that it doesn't fill up Logs when kicker is at rates less than 120Hz.


2012-05-18-a
------------
Update PICM:BSYA to be nonrecoverable.

2012-05-05-a
------------
Add XCOR BSYA Input


2012-04-30-a
------------
* reverted to 2012-03-20-a, 2012-04-22-a had PICM:BSYA channel errors
* Added Link Node 43 for A-Line KICKER (BYKICK TYPE)
* Added inputs in LN42 and 43 for A-Line

2012-04-22-a
------------
* Added Link Node 42 for A-Line PICs along with A-LINE PICMs.

2012-03-20-a
------------
* Added new CXI Valve
* Fix Input typos in LNW_BSO and STPR_BSY_88

2012-01-06-a
------------
* New HXRSS HOZ and YAW Home Status
* Puleo Chassis Updates

2012-01-03-a
------------
* New Fast Shutter in UND Name= VVFS:DMP1:107


2011-11-29-a
------------
* Changed A-Link Kicker Pulser status 1 & 2 per Tony Beukers


2011-11-15-a
------------
* Added new MPS inputs for A-Link Kicker Pulser status 1 & 2

2011-11-07-a
------------
* Adds new inputs for CXI and MEC.

2011-10-31-a
------------
* Add inputs for HXRSS system, re-assigned some iMPS inputs that are not used in logic for HXRSS
* Add RTD soft input for past SL10 A-Line

2011-09-12-a
------------
* Per Mark Arndt The change will be redefining Link Node 40 input on card 4 channel 14.
The new definition is:
[40,  4,   14,  "MEC:HXM:MMS_04:B", "POSITION", "IS_NOT_OUT", "IS_OUT", true, "MEC HXM reference laser mirror out of beam"]


2011-08-26-a
------------
* Per Mark Arndt and CXI: make inputs for the following Logic tables not autorecover 
	CXI CS-PAD 1 Detector Damage Fault
 	CXI CS-PAD 2 Detector Damage Fault
 	XPP CS-PAD 1 Detector Damage Fault

2011-08-01-a
------------
* Per Mark Arndt, add new devices per patch files

2011-07-12-a
------------
* Per Mark Arndt, 
Config and Logic changes are:

Link Node 40 card 1, channel 16  is now CXI_DSU_MMM_07_B_POSITION 
	becomes   CXI_DSD_MMS_07_B_POSITION
Link Node 40 card 6, channel 2   is now XCS_DG3_VGC_01_OPN_DI_POSITION
	becomes   CXI_DSU_MMS_07_B_POSITION

*XCS_DG3_VGC_01_OPN_DI_POSITION is removed from configuration 
	DB and logic DB device list. It was not used on any
	logic tables.

* Add new device (rename a junk name to new device
	CXI_DSD_MMS_07_B_POSITION)
* Change name of CXI_DSU_MMM_07_B_POSITION to CXI_DSU_MMS_07_B_POSITION
* Add revised CXI_Config4 logic C code
* Update CXI_Config5 with name modification (CXI_DSU_MMM_07_B_POSITION 
	to CXI_DSU_MMS_07_B_POSITION)


2011-07-05-a
------------
* Per Mark Arndt, add devices:

    HXX_HXM_MMS_01_B_POSITION
    HXX_MPS_PLC_01_OK_STATUS
    STPR_XRT1_1_S4IN_POSITION
    STPR_XRT1_1_S4OUT_POSITION
    STPR_XRT1_1_S6IN_POSITION
    STPR_XRT1_1_S6OUT_POSITION
    XCS_MPS_PLC_01_OK_STATUS
    XPP_MPS_PLC_01_OK_STATUS


2011-06-15-a
------------
* Per Mark Arndt
* Add XCS inputs, per database patch FEH_XCS_MPS_Patch_File_June2011_r1.json
* Remove obsolete XRT input:
  "XRT:DIA_DET:01:MPSFAULT"

* Clean-up: Remove obsolete FEE stopper inputs:
  "PPS_FEE1_1_STPR01_IN_POSITION"
  "PPS_FEE1_1_STPR01_OUT_POSITION"

2011-05-11-a
------------
*Per Mark Arndt add additional CXI inputs
   change PV Fault/Ok string names for 
  Card 4, channel 4, "CXI:DET_01:MPSFAULT"
  Card 4, channel 5, "CXI:DET_02:MPSFAULT"
  Card 4, channel 6,  "CXI:USR_01:MPSFAULT"
  Card 4, channel 7,  "CXI:USR_02:MPSFAULT"

  In each case, the label for the low/deasserted state should 
     change from "IS_NOT_FAULTED" to "IS_FAULTED".
  Also, the label for the high/asserted state 
        should change from "IS_FAULTED" to "IS_OK".

* Add new RTD soft input for BSY Past D2 per Sonya

Also, the label for the high/asserted state should change from "IS_FAULTED" to "IS_OK".

2011-05-05-a
------------
* Per Mark Arndt and CXI request, added CXI inputs
* Added D2 status

2011-02-26-a
------------
* Per Mark Arndt and CXI request, added EPICS input XRT:DIA_DET:01:MPSFAULT
for "CXI CS-PAD-Damge Fault" logic

2011-02-2-a
------------
* Added BSY PICM HV readback

2011-01-08-a
------------
* Renamed PV attribute of "MPS_STATE" to "PEAKPOWER" for MPS device FLT_20_6_TRP. Also changed OK and Fault name, signal is OK in low state and faulted in high.


2010-12-01-a
------------
* Removed extra HXX:MXT:VGC_01:OPN_DI Position input and removed from logic 

2010-11-29-a
------------
* Added additional CXI MPS inputs per Mark Arndt in LN 40. Re-patched based on 2010-09-28a 

2010-11-22-b
------------
* Added additional CXI MPS inputs per Mark Arndt in LN 40. 

2010-11-22-a
------------
* Added CXI MPS inputs per Mark Arndt in LN 40

2010-09-28a
------------
* Change name and unit # for "TRHZ:DMP1:310" to "THZR:DMP1:350"

2010-09-24a
------------
* Added "VVMG:DMP1:743"

2010-08-300a
------------
* Added "NEH AMO End Station Ready AMO-EXP-MPS-01"

2010-08-17-a
------------
* Added BYKICK watchdog 

2010-08-11-a
------------
* Added A-Line PICM BSYA:1701A and BSYA:1701B  (not auto recoverable)

2010-08-10-a
------------
* Corrected Faulted State Name for:
   "PROF:BSYA:1:OUT_SUM"
   "BEND:BSYA:140:B1_2_PS_ON"
   "COLL:BSYA:1015:FLOW_SW"
   "VVFS:BSYA:1030:POSITION"
   "VVPG:BSYA:1018:POSITION"
* Changed PICM:BSYA to not auto recoverable

2010-08-04-a
------------
!NOTE: based on 2010-07-06-a 
* Added more A-line devices (PICS, EPICS, Digital) 

2010-08-03-a
------------
* Added more A-line devices

2010-07-29-a
------------
* Added A-line devices (including PICs)

2010-07-06-a
------------
* Made BSY PIC inputs latching

2010-06-30-a
------------
* 11/3/12: DUMP_LI21_FLSW_OPEN -> COLL_LI21_235_OPEN
* 11/3/12: DUMP:LI21:305:FLOW_SW_MPSC -> COLL:LI21:235:FLOW_SW_MPSC

2010-06-21-a
------------
* Added LN 25 PIC inputs

2010-06-16-b
------------
* Added NO_TRIG inputs to LN 11, 16, and 22

2010-06-16-a
------------
* Removed PIC autorecover

2010-06-15-c
------------
* Removed PICs from LN 23, 25, and 26

2010-06-15-b
------------
* Corrected Link Node types

2010-06-15-a
------------
* Added PIC Inputs for
    * 11/1/1
    * 11/1/2
    * 11/1/3
    * 11/1/4
    * 11/1/5
    * 11/1/6
    * 16/1/1
    * 16/1/2
    * 22/1/1
    * 22/1/2
    * 22/1/3
    * 22/1/4
    * 22/1/5
    * 22/2/1
    * 22/2/2
    * 22/2/3
    * 22/2/4
    * 22/2/5
    * 23/1/1
    * 25/1/1
    * 25/1/2
    * 25/1/3
    * 25/1/4
    * 25/1/5
    * 25/1/6
    * 25/1/7
    * 25/1/8
    * 26/2/1
    * 26/2/2
    * 26/2/3
    * 26/2/4
    * 26/2/5

2010-05-20-b
------------
* Made TORO:IN20:971 inputs latching.

2010-05-20-a
------------
* Renamed BLM:UND1:4:TIMING(_L, _H, _1_L, _1_H) to
  BLM:UND1:4:HRTBT(_L, _H, _1_L, _1_H).

2010-05-04-a
------------
* Made BYKIK thresholds latching.

