************************* B4C must be out Date: Wed, 26 Jun 2013 10:35:56 -0700 From: "Stanek, Michael W." To: "Boyes, Matthew" Cc: "Turner, James L." , "Rogind, Debbie" , "Hoobler, Sonya" Subject: RE: New MPS interlock- fault on B4C IN status Matt, 1. This is not urgent in my opinion, since we have been running with this same risk for the past 2 years. It is unlikely the B4C can end up partially in the beam without being noticed. Schedule the release for when resources are available. If you and Sonya are not available next week, it can wait until the next release opportunity after that. 2. B4C was not disabled out. Stan Mao and Jim Turner decided that since B4C is supposed to 'protect' ST1 & 2, it would not be good to disable it out, thus removing a potential level of protection if MPS failed or was bypassed. 3. My request was made assuming you only have one microswitch (IN). That was mentioned at the meeting, and no objection was raised. 4. Yes, define the ignore logic the same as we did with ST1/ST2. Thanks for checking, -Mike -----Original Message----- From: Boyes, Matthew Sent: Tuesday, June 25, 2013 9:43 PM To: Stanek, Michael W. Cc: Turner, James L.; Rogind, Debbie; Hoobler, Sonya; Boyes, Matthew Subject: Re: New MPS interlock- fault on B4C IN status Thanks Mike. A few questions: 1. Do you know when this is required? Sonya and I will not be in on 7/3 for the PAMM. We each have scheduled vacations. 2. Do you know if the B4C was successfully disabled by turning the air off as Jim discussed? 3. As I pointed out in the meeting, MPS only has IN/NOT_IN status. I noticed your logic only makes use of IN status. Do those defining the requirement understand that the moving condition is NOT part of the protection? 4. I noticed your cater request doesn't correctly state the upstream destination devices that would ignore this logic. If it's OK, well define the ignore devices the same as we did for the ST1/ST2 logic. Is it OK if this doesn't get released next week? As we did with ST1/ST2, we will send you a draft of the MPS logic changes for Jim and your approval. Thanks, Matt -------------------------------------------- Matt Boyes SLAC National Accelerator Laboratory 2575 Sand Hill Rd MS 50 Menlo Park, CA 94025 mboyes@slac.stanford.edu Phone: (650)926-5204 On Jun 25, 2013, at 4:43 PM, "Stanek, Michael W." wrote: Matt, As we discussed in yesterday's meeting on the requirements for FEE ST1/2 and B4C interlocks, our interim solution will require a new MPS interlock to fault if the B4C block in ST0 goes IN. This fault can be masked with 'Ignore Logic' for all of the MPS upstream dumps, stoppers, magnets, OTRs. I have entered a Software Request in CATER to track this (CATER 109199). Thanks, Mike ************************* M1S protection From: "Smith, Tonee J." To: "Hoobler, Sonya" Subject: FW: energy limit for M1S Parts/Attachments: 1 Shown ~38 lines Text 2 OK ~108 lines Text ---------------------------------------- 6.75 GeV is the maximum Bend energy for M1S to be anywhere but OUT. From: Turner, James L. Sent: Tuesday, July 09, 2013 11:32 AM To: Smith, Tonee J. Subject: Re: energy limit for M1S Hi Tonee, These were limits for HOMS. We are protecting SOMS. SOMS we know will break around 2150-2200 eV from calculation and should be limited to less, so please set limit at 2024 eV allowing us to run at 2000 eV. This is 6.75 GeV electrons. ..Jim ************************* Logic differences [sonya@lcls-dev2 algorithm]$ sdiff -bs 2013-06-15-a/doc/MPSLogicDocumentation.txt 2013-07-08-a/doc/MPSLogicDocumentation.txt .. title:: MPS Logic 2013-06-15-a | .. title:: MPS Logic 2013-07-08-a > Ignored when BX01/BX02 Is Off, BXG Is On, ST1/ST2 Are In, Sto > ============================================================= > > FEE1 M1S Mirror Beam Energy Upper Limit > --------------------------------------- > ========================================= = = = ============= > Name C B A Pockels C > ========================================= = = = ============= > Fault F F F > Limit switch inconsistent F F T > Limit switch inconsistent F T F > OK F T T > OK T F F > Energy safe but limit switch inconsistent T F T > Energy safe but limit switch inconsistent T T F > OK T T T > ========================================= = = = ============= > > Where:: > > A = MIRR_FEE1_1560_OUT_LIMIT1_POSITION > B = MIRR_FEE1_1560_OUT_LIMIT2_POSITION > C = MIRR_FEE1_1560_ENERGY_STATE > > > > B4C Position > ------------ > ==== = ==================== ==================== ============ > Name A Pockels Cell Mechanical Shutter BYKIK > ==== = ==================== ==================== ============ > F 0 Hz 0 Hz > T 120 Hz 120 Hz > ==== = ==================== ==================== ============ > > Where:: > > A = YAG_DMP1_500_FLT2_OUT_POSITION > >