MpsConfiguration-R2-79 Logic 2018-08-28-a ------------- * Remove XLEAP Wiggler - Downstream End Vertical Gap Too Small XLEAP Wiggler - Upstream End Vertical Gap Too Small * Remove ignore logic XCS Is Not In Main Line Affected truth tables: XCS SB1 VGC 01 Gate Valve Position XCS SB1 VGC 02 Gate Valve Position XCS SB2 VGC 01 Gate Valve Position XCS SB1 Diagnostic Stopper Position MpsConfiguration-R2-78 Logic 2018-03-21-a ------------- * Set OTR30 truth tables inactive: OTR30 LTU1 449 Position OTR30 LTU1 449 Position When TDUND Not In NOTE: Do not use MpsConfiguration-R2-77 MpsConfiguration-R2-77 MpsConfiguration-R2-76 Config 2018-03-02-a ------------- * Remove MFX_LENS_1_SAFE Logic 2018-03-02-a ------------- * Remove MFX Beam Focusing Interlock (Beryllium Lens) MpsConfiguration-R2-75 Config 2017-12-13-a ------------- * Change all PIC/BLM loss and test inputs to be non-autorecoverable (latching). Most already had this setting, but a small number had been misconfigured. * Delete all rate-based PIC/BLM loss inputs. These were intended for rate-recovery, whose prospects are currently unknown and these input state changes flood the log. Logic 2017-12-13-a ------------- * XLEAP MIRXL - MIRR LTU1 829 Position: Make 3 mm position allowed (change rate from 0 -> 120 Hz) MpsConfiguration-R2-74 Config 2017-10-17-a ------------- * Add A-line secondary target IN/OUT status Logic 2017-10-17-a ------------- * Set 'Main Manifold Gauge: LI30 Station 9' Inactive * Set 'XCS Gate Valve Summary - XRT Periscope Line' Inactive * Rename FEE camera 852 and 913 logic to be more accurate MpsConfiguration-R2-73 Config 2017-07-24-a ------------- * New input XCS:PBT:VGC_OUT_SUM Logic 2017-07-24-a ------------- * New truth table XCS Gate Valve Summary - XRT Persicope Line MpsConfiguration-R2-72 Config 2017-06-19-a ------------- * Swap XLEAP mirror 3mm and 5mm position inputs (they are currently reversed). Logic 2017-06-19-a ------------- * Swap XLEAP mirror 3mm and 5mm position inputs (they are currently reversed). MpsConfiguration-R2-71 Logic 2017-06-08-b ------------- * Rename M3H to XRT-M2 in logic truth table names and state names * XRT-M2 (aka M3H) no longer has valid in position; deactivated related logic * FEE camera 852 and 913 FEE PLC interlock logic now does photon transmission check; updated truth table names and state names accordingly * Updated truth table names for A-line kickers now that kickers have been re-named as part of BSY Reconfiguration. (LN inputs still need rename eventually.) Config 2017-06-08-a ------------- * New inputs for XLEAP wiggler gap and insertable devices Logic 2017-06-08-a ------------- * New logic for XLEAP wiggler gap and insertable devices Config 2017-05-24-a ------------- * Remove obsolete inputs: THZR_DMP1_350_OUT_LIMIT THZR_DMP1_350_IN_LIMIT Logic 2017-05-24-a ------------- * Remove obsolete truth tables: THz Radiator Beryllium Foil FEE Camera 1561 Position MpsConfiguration-R2-70 Config 2017-05-22-a ------------- * Add inputs for XLEAP LTU Beam Loss Fiber Logic 2017-05-22-a ------------- * Add logic for XLEAP LTU Beam Loss Fiber Logic 2017-05-18-h ------------- * Add D2 as ignore device for PIC Trigger Missed (LN31) Logic 2017-05-18-g ------------- * Add YAG01, YAG02, TD11 as ignore devices for Linac PIC truth tables Logic 2017-05-18-f ------------- * Add TD11 as ignore device for Linac truth tables downstream of TD11 Logic 2017-05-18-e ------------- * Reinstate TDUND as an ignore device for some end-of-LTU BLMs. (It was removed in 2017-05-18-a.) See changes.log for more details. Logic 2017-05-18-d ------------- * Add missing ignore devices for PIC Trigger Missed (LN25) BCS PIC RAW Charge Threshold DMP 997 BCS PIC RAW Charge Threshold DMP 998 Logic 2017-05-18-c ------------- * Add missing D2 ignore device to more LTU truth tables. Logic 2017-05-18-b ------------- * More ignore logic cleanup. Add D2 as ignore device for injector OTRs when 'TDUND Not In' Logic 2017-05-18-a ------------- * Fix: Remove TDUND as ignore condition for many LTU truth tables. Unclear why it was in the list originally. Logic 2017-05-17-a ------------- * Add D2 Stopper Summary In as ignore condition for many LTU, UND, DMP truth tables. * Add TD11 as ignore condition for VVMG LTU1 505 Position MpsConfiguration-R2-69 Logic 2017-05-16-a ------------- * Allow 120 Hz beam when D2 is IN MpsConfiguration-R2-68 Config 2017-05-13-a ------------- * Remove OTR22 inputs: OTRS_LI25_342_OUT_LMTSW OTRS_LI25_342_IN_LMTSW * For 2017 FEE reconfiguration, many changes. See changes.log and supporting files for details. Logic 2017-05-13-a ------------- * Remove OTR22 truth tables: OTR22 Position OTR22 Position When TDUND Not In * For 2017 FEE reconfiguration, many changes. See changes.log and supporting files for details. MpsConfiguration-R2-67 Config 2017-05-10-b ------------- * New A-line valve VVPG_BSYA_340_OPEN_LIMSW * Remove long-obsolete devices: DEV_52SL1 DEV_50B1 DEV_50PR3OUT HVPS_BSY0_54_POWER * Remove inputs not needed for BSY Reconfiguration: TRGT_BSYA_960_OUT_LIMSW TRGT_BSYA_960_IN_LIMSW TRGT_BSYA_960_FLOW_SW TRGT_BSYA_960_KLIXON COLL_BSYH_479_FLOW_SW COLL_BSYH_487_FLOW_SW COLL_BSYH_495_FLOW_SW COLL_BSYH_520_FLOW_SW Logic 2017-05-10-b ------------- * Logic for new A-line valve: VVPG BSYA 340 Position * Remove inactive obsolete logic DEV 50PR3 Position * Per K. Jobe, remove logic associated with A-line copper target: A-Line Secondary Target Position A-Line Secondary Target Flow Switch A-Line Secondary Target Klixon A-Line Secondary Target Is Out Logic 2017-05-10-a ------------- * Remove references to obsolete FEE Spoiler SP0 and Stoppers ST1/ST2: - Remove truth tables: Spoiler SP0 DMP1 765 Position Stopper: ST1/ST2 Position - Remove ignore logic: Spoiler SP0 Is In ST1/ST2 Are In MpsConfiguration-R2-66 Config 2017-04-28-a ------------- * Replace individual PCAPM flow switches with single switch for PCAPM1-4 * Changed PIC channel assignments for PCAPM1-4 PICs * Remove unused constantly cycling PIC inputs for new BSYH PICs. Note will need to be re-added to implement rate recovery! Logic 2017-04-28-a ------------- * Remove: PIC Raw Charge Thresholds: BSYH 520 PCBSYH/A Flowswitch: COLL BSYH 520 (PCBSYH/A) Flowswitch: COLL BSYH 479 (PCAPM1) Flowswitch: COLL BSYH 495 (PCAPM3) Flowswitch: COLL BSYH 487 (PCAPM2) * Add: Flowswitch: COLL BSYH 479, 487, 495, 503 (PCAPM1-4) MpsConfiguration-R2-65 Config 2017-04-17-a ------------- Many changes to support 2017 downtime BSY Reconfiguration of LCLS common-line, including some A-line related changes. See changes.log and the other supporting documents for details. Logic 2017-04-17-a ------------- Many changes to support 2017 downtime BSY Reconfiguration of LCLS common-line, including some A-line related changes. More details can be found in changes.log and the other supporting documents. * Change 'A-Line B1/B2 Is Not On AND A-Line Kicker Is Not Enabled' to 'A-Line Kicker Is Not Enabled' * Change 'BSY GLAST Target' to 'A-Line Secondary Target' (target now in A-line; no longer in common-line) * Add new truth tables: Flowswitch: COLL BSYH 479 (PCAPM1) Flowswitch: COLL BSYH 487 (PCAPM2) Flowswitch: COLL BSYH 495 (PCAPM3) Flowswitch: COLL BSYH 503 (PCAPM4) Flowswitch: COLL BSYH 520 (PCBSYH/A) PIC Raw Charge Thresholds: BSYH 479 (PCAPM1) PIC Raw Charge Thresholds: BSYH 487 (PCAPM2) PIC Raw Charge Thresholds: BSYH 495 (PCAPM3) PIC Raw Charge Thresholds: BSYH 503 (PCAPM4) PIC Raw Charge Thresholds: BSYH 520 PCBSYH/A PIC Raw Charge Thresholds: BSYH 762 PC90 PIC Raw Charge Thresholds: BSYH 836 PC119 Temperature RTD Summary: BSY Common Line VVFS CLTH 101 Position VVPG BSYH 470 Position VVPG BSYH 541 Position VVPG BSYH 837 Position VVPG CLTH 178 Position VVPG CLTH 375 Position * Remove obsolete truth tables PIC Raw Charge Thresholds: BSY0 16 PIC Raw Charge Thresholds: BSY0 33 PIC Raw Charge Thresholds: BSY0 45 PIC Raw Charge Thresholds: BSY0 59 PIC Raw Charge Thresholds: BSY0 78A PIC Raw Charge Thresholds: BSY0 78B DPS Temperature LI30 Fast Shutter FV2A LI30 Position Fast Shutter FV2 LI30 Position VVPG BSY0 IV2 Position VVPG BSY0 IV3 Position VVPG BSY0 IV4 Position Temperature RTD Summary: BSY Common Line Before D2 Temperature RTD Summary: BSY Common Line Past D2 Ion Chamber Gas Flowswitch BSY A Ion Chamber Gas Flowswitch BSY B Ion Chamber Gas Flowswitch BSY C Flowswitch: BSY PC320 Flowswitch: BSY PC90 Flowswitch: COLL BSY0 16 (50PC20) Flowswitch: COLL BSY0 33 (50PC30) Flowswitch: COLL BSY0 45 (50PC-45) Flowswitch: COLL BSY0 59 (PC0119) Flowswitch: COLL BSY0 65 (PC0145) Flowswitch: COLL BSY0 67 (PC0155) Flowswitch: COLL BSY0 69 (PC0165) Flowswitch: COLL BSY0 71 (PC0175) Flowswitch: COLL BSY0 73 (PC0185) Flowswitch: COLL BSY0 75 (PC0195) MpsConfiguration-R2-64 Logic 2016-11-09-a ------------- * Remove 'MFX Gate Valves Not All Open - PLC Summary Status' * Rename 'Toroid Comparator Dogleg (IM02 vs IM03)' to 'Toroid Comparator Dogleg 1 (IM02 vs IM03)' MpsConfiguration-R2-63 Logic 2016-11-03-a ------------- * Modify titles of toroid comparator truth table names for clarity Logic 2016-10-20-a ------------- * Add ignore condition 'BSY GLAST Target Is Out' * Modify 'BSY GLAST Target Klixon' and 'BSY GLAST Target Flow Switch' to use above ignore condition instead of using the target position in the actual truth table Config 2016-10-19-a ------------- * Delete obsolete device inputs: Dump B4C BSY PR45 BSY PR55 Logic 2016-10-19-a ------------- * Delete obsolete and inactive logic: Profile Monitor BSY0 55 MpsConfiguration-R2-62 Logic 2016-10-18-a ------------- * Remove truth tables: Profile Monitor BSY0 45 Position When D2 or TDUND Not In Profile Monitor BSY0 45 Position Logic 2016-10-17-a ------------- * New MFX interlocks * Add new analog link node inputs (not yet used in logic) Config 2016-10-17-a ------------- * Add new MFX inputs. See changes.log and *diff*.html files for details MpsConfiguration-R2-61 Logic 2016-08-25-a ------------- * Build against database 2016-08-25-a in order to test analog link node inputs. No logic changes. Config 2016-08-25-a ------------- * Add new Analog Link Node 44 and first set of inputs See changes.log for details MpsConfiguration-R2-60 Logic 2016-05-10-a ------------- * Again, minor change to state names for these truth tables: FEE Spectrometer Crystal - Beam Energy Too Low When Crystal Not Out FEE Spectrometer Crystal - Pulse Energy Too High When Crystal Not Out Gas Detector Problem When FEE Spectrometer Crystal Not Out Config 2016-05-02-a ------------- * Remove unused and obsolete device TIUKEYSW aka TIU:IN20:1:KEY_SWITCH_STATE Logic 2016-05-02-a ------------- * Remove unused and obsolete device TIUKEYSW aka TIU:IN20:1:KEY_SWITCH_STATE * Rename Spoiler: SP0 DMP1 765 Position to Spoiler SP0 DMP1 765 Position MpsConfiguration-R2-59 Logic 2016-04-29-a ------------- * Minor change to state names for these truth tables: FEE Spectrometer Crystal - Beam Energy Too Low When Crystal Not Out FEE Spectrometer Crystal - Pulse Energy Too High When Crystal Not Out Gas Detector Problem When FEE Spectrometer Crystal Not Out MpsConfiguration-R2-58 Config 2016-04-26-a ------------- * Delete obsolete dechirper devices DCHP_LTU1_545_WDOG_SUM DCHP_LTU1_545_BPM_INTOL * New devices for FEE spectrometer crystal protection XTAL_FEE1_441_PULSEENERGY, LN10, Card 4, Ch 3 GDET_FEE1_1_CAL_OK, LN10 Card 4, Ch 4 Logic 2016-04-26-a ------------- * New truth tables for FEE spectrometer crystal protection FEE Spectrometer Crystal - Pulse Energy Too High When Crystal Not Out Gas Detector Problem When FEE Spectrometer Crystal Not Out Logic 2016-04-24-a ------------- * No logic changes. Modify Makfile to use scripts/version1-0-6 Config 2016-04-24-a ------------- * No config changes. Modify Makfile.conf to use scripts/version1-0-6 MpsConfiguration-R2-57 Logic 2016-03-01-a ------------- * "FEE Solid Attenuators - Gas Pressure Interlock": allow SATTs 3 and 4 to be IN Logic 2016-02-26-a ------------- * Remove obsolete inputs and associated logic - should not affect algorithm Logic 2016-02-25-a ------------- * Remove obsolete inputs and associated logic - should not affect algorithm Logic 2016-02-24-a ------------- * Remove Dechirper BPM interlocks * Remove dangling unused database objects - should not affect algorithm MpsConfiguration-R2-56 Logic 2016-02-12-a ------------- * Update LTU Horizontal Dechirper Gap truth table now that we have 2 independent gap switches MpsConfiguration-R2-55 Logic 2016-01-22-b ------------- Remove LTU Dechirper - 10 Hz Rate Limit if Dechirper Not Out Logic 2016-01-22-a - BASED ON 2015-12-17-a ------------- Rename some inputs to match their PV names. See changes.log for details. Config 2016-01-22-a ------------- * Rename some input names to match their PV names. See changes.log for details. MpsConfiguration-R2-54 Config 2015-12-07-b ------------- * Removed unused PV attributes from database. For some External PV objects, fill in missing Device Details fields. See changes.log for details. Config 2015-12-07-a ------------- * Removed unused devicedetails and fault objects from database: Devicedetails: THZR LTU1 741 IN_LIMSW MIRR FEE1 1560 OUT_LIMIT1 (two of these) MIRR FEE1 1560 OUT_LIMIT2 (two of these) XTAL FEE1 441 OUT_LIMSW Faults: 'SPARE' '02B' '02A' 'Valve is open' 'A-line Kicker Pulser1': PULSER1_ON, PULSER1_OFF, PULSER1_TRIG_ENB, PULSER1_TRIG_LOCK 'A-line Kicker Pulser2': PULSER2_ON, PULSER2_OFF, PULSER2_TRIG_ENB, PULSER2_TRIG_LOCK 'SL10 CLOSED' 'ST22 OUT' 'THZ-2 Foil Out Switch' 'THZ-2 Foil In Switch' 'FEE spectrometer crystal OUT' Config 2015-12-01-a ------------- * Removed duplicate device instances: MIRR_FEE1_1560_OUT_LIMIT1 (2 duplicates) MIRR_FEE1_1560_OUT_LIMIT2 (2 duplicates) XTAL_FEE1_441_OUT_LIMSW (1 duplicate) Config 2015-11-30-a ------------- * Remove duplicate PvArea LTU1 from database. Changed all devices that used the deleted instance to use the other instance. See changes.log for list of affected devices. * Remove duplicate PvDeviceType BFW from database. Changed all devices that used the deleted instance to use the other instance. See changes.log for list of affected devices. Config 2015-11-23-a ------------- * Remove unused devices: FLOOD_SW_OK TARGET_EPV_FLOSW_2_OK AMO_HFP_MPA_02ASPARE MTLM_LOGIC_OK STOPPER_2_IN_OUT STOPPER_1_IN_OUT AMO_HFP_MPA_02BSPARE RAD_SHLD_FLOSW_9_OK * Remove unused LN channels LN 40 Card 1 Channel 10 LN 40 Card 1 Channel 11 LN 40 Card 2 Channel 9 LN 40 Card 2 Channel 10 LN 40 Card 2 Channel 11 LN 40 Card 3 Channel 11 LN 42 Card 2 Channel 4 LN 42 Card 2 Channel 6 LN 42 Card 3 Channel 8 Logic 2015-12-17-b ------------- Remove LTU Dechirper - 10 Hz Rate Limit if Dechirper Not Out Logic 2015-12-17-a - BASED ON 2015-11-09-a ------------- * Remove unused duplicate truth table * Fix XRT S5 state names (Moving and Broken were swapped) * Update LTU Vertical Dechirper Gap truth table now that we have 2 independent gap switches MpsConfiguration-R2-53 Config 2015-11-09-a ------------- * Add MEC_DV4_VGC_01_OPN_DI * Misc LN 39-41 rename and delete for photon-side inputs. Details in directory. Logic 2015-11-09-b ------------- Remove LTU Dechirper - 10 Hz Rate Limit if Dechirper Not Out Logic 2015-11-09-a - BASED ON 2015-10-10-a ------------- * Remove photon logic: HXX:HXM:VGC:01 Gate Valve Position HXX:HXM:VGC:02 Gate Valve Position HXX:HXM:VGC:03 Gate Valve Position XRT HXRAY MXT Isolation Valve HXX-MXT-VGC-01 NEH AMO Focusing Optics Entrance Gate Valve KBO-VGC-01 NEH AMO Focusing Optics Exit Gate Valve KBO-VGC-02 NEH AMO LAMP Gate Valve VGC 30 Position NEH AMO LAMP Gate Valve VGC 30 Is In Beam NEH AMO LAMP Gate Valve VGC 30 Is Out of Beam * Add photon logic: NEH AMO Valves Ok for Beam - Summary From PLC MEC BXL VGC 01 Gate Valve Position XRT HXRAY MXT Gate Valve HXX:MXT:VGC:01 XRT HXRAY MXT Gate Valve HXX:MXT:VGC:02 XRT HXRAY MXT Gate Valve HXX:MXT:VGC:03 XRT HXRAY MXT Gate Valve HXX:MXT:VGC:05 * Add ignore devices to TDUND Position * Remove B4C Position * Remove Temperature RTD Summary: North Arc MpsConfiguration-R2-52 Logic 2015-10-10-b ------------- Remove LTU Dechirper - 10 Hz Rate Limit if Dechirper Not Out Logic 2015-10-10-a ------------- Remove LTU Dechirper - Undulators Must Be Out If Dechirper Not Out Logic 2015-10-09-a - BASED ON 2015-09-08-a ------------- Add MEC DV4 VCG 01 Gate Valve Position Use database version 2015-10-09-a Config 2015-10-09-a ------------- * Add MEC_DV4_VGC_01_OPN_DI MpsConfiguration-R2-51 Logic 2015-09-08-z: NON-LINEAR LOGIC ------------- This is a version to be used ONLY for LTU Dechirper commissioning. It is based on 2015-09-04-a with these changes: * Add commissioning Dechirper logic: LTU Dechirper Commissioning - BPM 550 Watchdog LTU Dechirper Commissioning - BPM 550 X/Y Position LTU Dechirper Commissioning - TDUND Must Be In Logic 2015-09-08-a ------------- * Add production Dechirper logic: LTU Dechirper - Undulators Must Be Out If Dechirper In LTU Dechirper - 10 Hz Raw Limit if Jaws Not Out LTU Dechirper - BPM 550 Watchdog LTU Dechirper - BPM 550 X/Y Position LTU Dechirper - Horizontal Gap Too Small LTU Dechirper - Vertical Gap Too Small Ignore device: LTU Dechirper Is Out Logic 2015-09-04-a ------------- * Add truth table "MFX Gate Valves Not All Open - PLC Summary Status" Logic 2015-09-03-a ------------- * Add truth table "VVFV IN20 785 Position" * Add Dechirper BLF truth tables: "BLM Heartbeat: Dechirper LTU1 BLF545" "BLM Pedestal Thresholds: Dechirper LTU1 BLF545" "BLM Raw Charge Thresholds: Dechirper LTU1 BLF545" * Set "XPP CS-PAD 1 Detector Damage Fault" inactive Config 2015-09-03-a ------------- * Add Dechirper inputs: BLM:LTU1:BLF545:LOSS_60_L BLM:LTU1:BLF545:LOSS_60_H BLM:LTU1:BLF545:TEST_L BLM:LTU1:BLF545:TEST_H BLM:LTU1:BLF545:TEST_1_L BLM:LTU1:BLF545:TEST_1_H BLM:LTU1:BLF545:PED_L BLM:LTU1:BLF545:PED_H * Add new IN20 fast valve: VVFV:LI20:785:OPEN_LMTSW * Add new MFX hutch vacuum valve PLC summary: MFX_MPS_PLC_VAC_OK MpsConfiguration-R2-50 Logic 2015-07-13-b ------------- * Explicity add inputs for is-code logic (those that were missing) to support MPS GUI improvements * Update logic for CXI:SC3:VGC:01. See changelog for details. MpsConfiguration-R2-49 Logic 2015-07-13-a ------------- * Add new truth table for CXI gate valve: "CXI:SC3:VGC:01 Gate Valve Position" * Modify BC1 toroid comparator state names to reflect new threshold Config 2015-07-13-a ------------- * Add Dechirper inputs: DCHP_LTU1_545_BPM_INTOL_THRESHOLD DCHP_LTU1_545_GAP_LIMSW_NEGZ_POSITION DCHP_LTU1_545_GAP_LIMSW_POSZ_POSITION DCHP_LTU1_545_OUT_LIMSW_NEGY_POSITION DCHP_LTU1_545_OUT_LIMSW_POSY_POSITION DCHP_LTU1_545_WDOG_SUM_STATE DCHP_LTU1_555_GAP_LIMSW_NEGZ_POSITION DCHP_LTU1_555_GAP_LIMSW_POSZ_POSITION DCHP_LTU1_555_OUT_LIMSW_NEGX_POSITION DCHP_LTU1_555_OUT_LIMSW_POSX_POSITION USEG_UND1_1_ALL_OUT_STATE * Add new CXI gate valve open limit switch: CXI_SC3_VGC_01_OPN_DI_POSITION MpsConfiguration-R2-48 Logic 2015-05-18-a ------------- * Add new truth table FEE Solid Attenuators - Gas Pressure Interlock * Modify ignore device lists for: HXR - Beam Energy Too Low With M1S Out FEE Spectrometer Crystal - Beam Energy Too Low When Crystal Not Out Config 2015-05-18-a ------------- * Add FEE Gas attenuator pressure threshold interlock to LN38: VMPS:FEE1:E202:NOGAS MpsConfiguration-R2-47 Logic 2015-05-04-a ------------- * Add new devices: LN42 trigger; LTU dechirper BLF * Add truth table PIC Trigger Missed (LN42) * Remove duplicate truth table Mirror BL21 Position * Per CATER request, add MAD names to OTR/YAG truth tables. Then, to be consistent, add unit numbers to other OTR/YAG truth tables Config 2015-05-01-a ------------- * Add LTU Dechirper Beam Loss Fiber channel to LN30: BLM:LTU1:BLF545 Config 2015-04-22-a ------------- * Add PIC LN 42 trigger input status, fault: PICM_BSYA_2061_NO_TRIG_MISSED MpsConfiguration-R2-46 Logic 2015-03-04-a ------------- * Add TD11 Position truth table to fault moving/broken state Logic 2015-03-02-c ------------- * Remove BX01/BX02 and BXG from ignore device lists for truth tables also ignored by TD11 * Remove duplicate Flowswitch: COLL BSYA 1015 (PC10) * Rename BSY GLAST Target to BSY GLAST Target Position * Remove duplicate Linac slow and fast valves Logic 2015-03-02-b ------------- * Rename TIU, flow switch, IMPS Heartbeat, Pockels Cell truth tables for clarity and consistency Logic 2015-03-02-a ------------- * Remove duplicate truth tables: TIU: DPS Temperature TIU: Fast Shutter 2 Position: LI30 TIU: Fast Shutter 2A Position: LI30 YG BL241 Position YG BL351 Position * Change TIU:MCC Emergency Radiation Stopper to be always evaluated (never ignored) * Add D2 as ignore device for HXRSS logic MpsConfiguration-R2-45 Logic 2015-01-07-b ------------- * NOTE: this version is a pseudo-branch, containing just 2 changes from 2015-01-07-a. Last-minute release to support LCLS MD activities: - Ignore 30-9 slow valve if TD11 is IN MpsConfiguration-R2-44 Logic 2015-01-07-a ------------- * Add TDUND flow switch logic * Reorganize Profile Monitor BSY0 45 logic to take advantage of ignore devices instead of using stopper positions as inputs to logic. Set 'Profile Monitor BSY0 45' logic to Not Active Add 2 new truth tables: 'Profile Monitor BSY0 45 Position' and 'Profile Monitor BSY0 45 Position When D2 or TDUND Not In' * Fix typo in truth table name. Change 'FEE Spectrometer Crystal - Beam Energy Too Low With Crystal Out' to 'FEE Spectrometer Crystal - Beam Energy Too Low When Crystal Not Out' MpsConfiguration-R2-43 Logic 2014-12-05-a ------------- * Add logic to protect FEE spectrometer crystal from low energy beam Config 2014-12-05-a ------------- * Add fault XTAL_FEE1_441_ENERGY * Rename XTAL_FEE1_442_OUT_LIMSW to XTAL_FEE1_441_OUT_LIMSW MpsConfiguration-R2-42 Config 2014-11-25-a ------------- * Add faults KICK:LTU0:320:ABORTWIN KICK:LTU0:320:STANDBYWIN MpsConfiguration-R2-41 Logic 2014-10-24-a ------------ * Add truth tables XPP SB2 VGC 02 Gate Valve Position XPP SB2 VGC 03 Gate Valve Position Config 2014-10-24-a ------------ * Add inputs XPP_SB2_VGC_02_OPN_DI_POSITION XPP_SB2_VGC_03_OPN_DI_POSITION MpsConfiguration-R2-40 Logic 2014-10-16-a ------------ * BCS PIC RAW Charge Threshold DMP 997/998: add D2 to ignore list * OTR21/OTR22 Position: add TD11 To ignore list * OTR30/OTR33 Position: add TD11 and D2 to ignore list Config 2014-10-16-a ------------ * Add FEE Spectrometer Crystal OUT limit switch MpsConfiguration-R2-39 Logic 2014-10-10-a ------------ * Set 'Stopper: ST1/ST2 Position' to only be ignored if D2 IN MpsConfiguration-R2-38 Logic 2014-10-01-a ------------ * Add HXR Beam Energy with M1S Out truth table MpsConfiguration-R2-37 Logic 2014-09-24-a ------------ * Cleanup of photon logic ignore device lists See changes.log for more information MpsConfiguration-R2-36 Logic 2014-09-23-a ------------ * Add new ignore device SP0 spoiler, add it as ignore device to appropriate truth tables MpsConfiguration-R2-35 Modify for cram and static build Added to CVS modules as MpsConfiguration **Note new tag names use capital M, i.e. MpsConfiguration, not mpsConfiguration** mpsConfiguration-R2-34 Logic 2014-07-02-a ------------ * Modify D2 logic to rate-limit beam to 10 Hz (from 120) when D2 is IN * Update PIC HVPS input names to be consistent * Add truth tables for missing PIC HVPS inputs: LI20, LI24, BSY * Fix ignore devices for LI24 BLM/PIC watchdog Config 2014-07-02-a ------------ * Add missing BSY PIC HVPS inputs: 2-6 * Update input and state names for all PIC HVPS to be consistent mpsConfiguration-R2-33 Logic 2014-06-09-a ------------ * Added logic for DMP SP0 Spoiler Position Config 2014-06-09-a ------------ * Added IN and OUT limit switches for DMP SP0 spoiler mpsConfiguration-R2-32 Logic 2014-05-30-a ------------ * Remove photon mirror M3H from lists of ignore devices mpsConfiguration-R2-31 Logic 2014-05-13-a ------------ * Remove CXI Detector Damage truth tables * Set B4C Protection of ST1/ST2 inactive * Update B4C Position * BSY RTD truth table name cleanup * Fix incorrect LHS mitigation rate assignment for some non-LHS-related truth tables mpsConfiguration-R2-30 Logic 2014-03-31-a ------------ * Update CXI valve logic per A. Wallace mpsConfiguration-R2-29 Logic 2014-03-12-a ------------ * Update CXI Configurations 2 and 7 per A. Wallace mpsConfiguration-R2-28 Logic 2014-02-28-a ------------ * Changed names and removed channels for CXI. * Updated CXI configuration summary logic * Added D2 as Ignore Device for many CXI truth tables Config 2014-02-28-a ------------ * Changed names and removed devices for CXI mpsConfiguration-R2-27 Logic 2014-02-26-a ------------ * Update SXRSS Mode logic; remove temporary mode truth tables that were created for commissioniNG mpsConfiguration-R2-26 Logic 2014-02-21-a ------------ * Cleaned up FEE1 M1S Mirror Beam Energy Upper Limit truth table mpsConfiguration-R2-25 Logic 2014-02-06-a ------------ * No logic changes * Use database 2014-01-06-a to pick up databaseCommon/version1-0-4, which adds channel access security to MPS bypasses Config 2014-02-06-a ------------ * Use databaseCommon/version1-0-4 to add channel acces security to MPS bypasses mpsConfiguration-R2-24 Logic 2014-01-06-a ------------ * 50PC30, 50PC45, PC0119 - no longer ignore when A-Line B1/B2 Is Not On AND A-Line Kicker Is Not Enabled (never should have been the case) * SXRSS: Add individual truth tables for each insertable device; Modify mode logic to take advantage of these new tables mpsConfiguration-R2-23 Logic 2013-12-17-a ------------ * SXRSS Mode: Seeded Mode: Allow M3 to be either IN or OUT (previously required to be IN) mpsConfiguration-R2-22 Logic 2013-12-02-a ------------ * Modifications to HXR Beam Energy Lower Limit for future use and set inactive for now * Add FEE1 M1S Mirror State to check for inconsistencies * Add S5B to ignore list for HF4 LAM VGC 01 Gate Valve Position * Add D2 to ignore list for B4C Protection of ST1/ST2 mpsConfiguration-R2-21 Logic 2013-11-11-a ------------ * Enable production SXRSS Mode State; disable temporary SXRSS Mode State - Chicane, Slit, and M3 Active mpsConfiguration-R2-20 Logic 2013-10-28-a ------------ * A-line IV40: Ignore when 'SL10 Closed' or 'B1/B2 Off and A-line Kicker not enabled' mpsConfiguration-R2-19 Config 2013-10-15-a ------------ * Remove AMO_HFP_VGC_02A, AMO_HFP_VGC_02B * Add AMO_LMP_VGC_30_OPN_DI, AMO_LMP_VGC_30_CLS_DI Logic 2013-10-15-a ------------ * Changes for next AMO run: -Remove NEH AMO Diagnostics Chamber Gate Valve -Remove ANEH AMO HFP Beam Stop -Remove NEH AMO End Station Ready -Remove NEH AMO High Field Physics Chamber Gate Valve Summary -Add NEH AMO LAMP VGC 30 Position truth tables mpsConfiguration-R2-18 Config 2013-10-10-a ------------ * Remove OTRS LTU1 743 OUT/IN LIMITs (PSI profile monitor) * Add YAGS LTU1 743 OUT/IN LIMITs (PSI profile monitor) Logic 2013-10-10-a ------------ * Modify PSI Profile Monitor truth table to use YAGS:LTU1:743 inputs instead of OTRS:LTU1:743 inputs; changed truth table name to use YAG instead of OTR mpsConfiguration-R2-17 Config 2013-10-04-a ------------ * Add OTRS LTU1 743 OUT/IN LIMITs (PSI profile monitor) Logic 2013-10-04-a ------------ * Add logic for SXRSS with Chicane, Slit, and M3 Active (for M3 test) * Remove previous M3 standalone logic; not needed * Add LTU PSI profile monitor logic mpsConfiguration-R2-16 Logic 2013-09-24-a ------------ * Add logic for BSY GLAST Target Flow Switch * Add logic for SXRSS M3 (temporary for test of mirror only) * Modify logic for BSY collimator 65, 67, 69, 71, 73, 75) flow switches so that they are not masked by "A-Line B1/B2 Is Not On AND A-Line Kicker Is Not Enabled" * Revive Inactive BSY GLAST Target Klixon with new logic Config 2013-09-24-a ------------ * Add BSY GLAST Target Flow Switch mpsConfiguration-R2-15 Logic 2013-08-28-a ------------ * Modify Ignore Device A-Line B1/B2 Is Not ON and A-Line Kicker Is Not Enabled: - Replace power supply ON status with 2 new OFF status inputs from PPS * Per R. Iverson, modify BSY PR45 logic to require D2 or TDUND to be IN if PR45 IN * Per R. Iverson, M. Stanek remove SXR lower energy limit Config 2013-08-28-a ------------ * Add A-line B1/B2 OFF status Chains A and B from PPS mpsConfiguration-R2-14 Logic 2013-08-02-a ------------ * Add SXRSS logic and devices; remove obsolete e+ devices * Active SXRSS logic assumes only slit and chicane are installed * Inactive SXRSS logic added for potential future use: - All SXRSS devices installed - slit, chicane, M2, M3 installed Config 2013-08-02-a ------------ * Add SXRSS devices mpsConfiguration-R2-13 Logic 2013-07-19-a ------------ * Per CATER 109696, add fault if A-line IV26 NOT_OUT * Add missing state names for B4C protection mpsConfiguration-R2-12 Logic 2013-07-08-a ------------ * Per Cater 109199, add logic that requires B4C in ST0 to be OUT * Per J. Turner (see algorithm/2013-07-08-a/changes.log) require FEE M1S Mirror to be OUT OR Beam Energy is low enough Database 2013-07-08-a --------------- * To support M1S mirror protection (above), add 2 OUT limit switch inputs and 'energy OK' input (this repurposes an unused LN11 input 'BC1_CID') mpsConfiguration-R2-11 Logic 2013-06-15-a ------------ * Per Cater#108919 Regarding mitigating potential B4C damage while running low energy. In attendance were Rad Physics, Paul Miller, John Arthur, Roger, Jim Turner, and M. Stanek. The interim solution for allowing low energy running without a BAS 2 mJ limit was an agreement that we would not allow photons on the ST0 B4C piece at all. Sayed Rokni accepted that as an interim measure, we would use MPS to ensure this condition. What is need required: If ST1/ST2 = Not OUT, Zero rate fault the Gun. This fault should have an 'ignore condition' when TDUND is in, D2 is in, TD11 is in, BX01/02 is NOT ON, YAG BL211 is IN, BXG is ON. Existing B4C ST1_ST2 shall stay in place. mpsConfiguration-R2-10 Logic 2013-06-13-a ------------ * Change D2 Stopper State Strings. Bit 0 and 1 were reversed. Change does not affect logic only readback status string mpsConfiguration-R2-09 Database 2013-06-03-a ------------ * Add GLAST Limit Switches Logic 2013-06-03-a ------------ * Add Logic for GLAST Target Moving * Add Logic for VAC Valve BSYA 4005 (IV40) mpsConfiguration-R2-08 Database 2013-05-27-a * Add new STPR 60 System (D2, ST60,ST61, BTM60,BTM PPS SOLN CNTL). Signals coming from PPS Logic 2013-05-27-a ------------ * Add New STPR 60 System C-code logic, all must be IN or OUT. Change Ignore logic status to use new D2 IN bits and De-Activate D2 Logic from BCS * Add TDUND IN to Prof BSY 45 logic per R.Iverson * De-Activate A-Line LGPS/COR magnets from A-Line logic per R. Iverson and J. Nelson - lgps ab01 1010, 1090, 1950, 2050, 2750, 2850, and xcor 2890, 3212, and ycor 2911, 3313. * De-Activate A-Line GLAST Klixon per R. Iverson and J. Nelson mpsConfiguration-R2-07 Logic 2012-12-10-a --------------------- * Changed HXRSS Mode logic per Heinz-Dieter Nuhn: - HXRSS bend lints changed from 12.7