GLT Cosmic run hardware status log 
==================================

(This is based on whatever was written down and is not a complete record)

Jan/9   First runs with DAQ data making sense
Run 253  DCH+IFR+DCT+GLT                    scint.   
Run 254        "                            A*>=1
Jan/11  We also saw EMT->GLT M signals on scope
Jan/13  New IFT prom to allow IFT trigger timing moved earlier by 1 tick. 
Jan/15(?) New FC prom fixed close trigger out of synch problem. 
Jan/22
Run 643 New GLT trigger definitions including combinations of IFT,EMT,DCT    
Jan/23 
Run 704 DCT A,B input delay timing adjustment DR2 delay 1b4b->1a2a 
Run 704-710 GLT IDAQ 3-word shift word format problem
Run 713-727                          "
Jan/24
Run 755 Corrected EMT->GLT cable 0-9 -> 1-10 (was 0->10 & 1-9 -> 1-9)  
Jan/28
Run 882--886 all had 3 word shift problem. Reset GLT Ok since 887.
Run 888  DCH+DIRC+IFR+EMC + DCT+EMT+GLT     scint.   50K 
Run 889  DCH+DIRC+IFR     + DCT+GLT         M*>=1    50K 
         (EMC+EMT running in separate partition not logging)
Run 890  DCH+DIRC+IFR+EMC + DCT+GLT         M*>=1   crashed ~3K   
   (891)  tried IFR trigger with EMC , crashed
Run 892  DCH+DIRC+IFR     + DCT+GLT         IFR=3    50K  (GLT 3-word shift)
Run 893  DCH+DIRC+IFR     + DCT+GLT         IFR=3    15K 
Run 894  DCH+DIRC+IFR     + DCT+GLT         A*>=1    17K crashed by DIRC  
                                                     (& GLT has 3-word shift)
Run 895+ DCH+DIRC+IFR+EMC + DCT+EMT+GLT     scint.   (checked GLT OK)
Jan/29
Run 940  DCH+DIRC+IFR+EMC + DCT+EMT+GLT     scint.   15K (GLT 3-word shift)
Jan/30  
Run 971                                                  (GLT 3-word shift)
Run 972  6AM  Checked GLT IDAQ mode OK.
Run 996  EMT and GLT data disagreement (EMT X seen as GLT E?)        
Run 1002 6PM  Checked GLT IDAQ mode OK.
Jan/31 
Run 1096 Last DCH cosmic run.
Feb/1 
Run  ?   GLT-3 was in the system temporarily for testing          
Feb/4
Run  ?  (1:45pm) New trigger lines with IFT+EMT only
   -----

Apr/18-Apr/24
GLT-2/GLT-3 were swapped many times for testing. GLT-2 data mostly had 
problems with IDAQ word shifts. GLT-3 had problems with event out of 
order errors for many events during this period.
Apr/18
DCT still using old firmware
Run 1404 First DCH->DCT->GLT calibration (TSFX cable error noticed)
Run 1405 2nd Calibration run. TSFX cable fixed. 
Apr/21
DCT upgraded to new firmware with block transfer
Run 1485 DCH->DCT->GLT calibration   (GLT-2)
Run 1488           "                 (GLT-3 block transfer download)
Run 1493           "                 (GLT-3 single write download)
    [GLT-3 data had DAQ event out of order problem]
Apr/22   
Run 1509 Installed new GLT trigger lines including DCT triggers.
         (prescales reset to=1 a few runs later).
Apr/24
Run 1582 GLT-3 left in running overnight (still has event out of order)
         (Also made small mod. to trigger line 7 (FEMC)) 
Run 1627 GLT-3 DAQ out of order problem fixed. GLT-3 Remain in IR2.
Run 1631 780Hz 1A trigger run to verify DAQ out of order fix.
Apr/27 
Run      (4:45pm) GLT lookup table M* skip 4->8, A*,B* skip 3->6    
Run 1817 First run after DCH repair (trigger mask=60).