Thumbnails

lab01.jpg
lab01.jpg

121.14 Kb
lab02.jpg
lab02.jpg

100.11 Kb
lab03.jpg
lab03.jpg

121.29 Kb
lab04.jpg
lab04.jpg

114.46 Kb
lab05.jpg
lab05.jpg

120.31 Kb
lab06.jpg
lab06.jpg

141.44 Kb
lab07.jpg
lab07.jpg

118.42 Kb
lab08.jpg
lab08.jpg

121.42 Kb
lab09.jpg
lab09.jpg

120.74 Kb
lab10.jpg
lab10.jpg

129.87 Kb
lab11.jpg
lab11.jpg

124.99 Kb
lab12.jpg
lab12.jpg

353.35 Kb
lab13.jpg
lab13.jpg

414.73 Kb

lab14.jpg
lab14.jpg

428.74 Kb

 

elab01.jpg
elab01.jpg

575.75 Kb
elab02.jpg
elab02.jpg

162.94 Kb
elab03.jpg
elab03.jpg

526.71 Kb
elab04.jpg
elab04.jpg

158.25 Kb
../overview/photos/elab05.jpg
elab05.jpg

530.98 Kb
../overview/photos/elab06.jpg
elab06.jpg

533.25 Kb
../overview/photos/elab07.jpg
elab07.jpg

569.61 Kb
../overview/photos/elab08.jpg
elab08.jpg

247.49 Kb
../overview/photos/elab09.jpg
elab09.jpg

230.76 Kb
../overview/photos/elab10.jpg
elab10.jpg

580.97 Kb
../overview/photos/elab11.jpg
elab11.jpg

541.28 Kb

../overview/photos/elab12.jpg
elab12.jpg

536.59 Kb

     

Descriptions

  • LAB photo1: Bill Sands on top of blue frame attaching crane straps (1)
  • LAB photo2: Bill Sands on top of blue frame attaching crane straps (2)
  • LAB photo3: Chamber hoisted out of blue construction frame
  • LAB photo4: Lowering chamber into temporary stands
  • LAB photo5: Rear endplate view of chamber sitting in temporary stands
  • LAB photo6: David Warner and Bill Sands preparing to remove rear spider
  • LAB photo7: Bill Sands removing spider mounts at front endplate
  • LAB photo8: Picking chamber out of cantilever stand
  • LAB photo9: Installing test stand into chamber suspended from crane
  • LAB photo10: Inserting test stand square beam into chamber
  • LAB photo11: Restoring chamber on test stand into LAB tent
  • LAB photo12: David Warner installing electronics arm (1)
  • LAB photo13: David Warner installing electronics arm (2)
  • LAB photo14: Test fit of one wedge of FEA boxes after electronics arm installation
  • LAB photo15: Philip finishing sensor cabling on DCH front end
  • LAB photo16: Rear endplate view with covers open (1)
  • LAB photo17: DCH seen from the rear with covers open
  • LAB photo18: Rear endplate view with covers open (2)
  • LAB photo19: Rear endplate view with covers open (3)
  • LAB photo20: Closeup of installed installed readout electronics with middle FEA box removed (1)
  • LAB photo21: Closeup of installed installed readout electronics with middle FEA box removed (2)
  • LAB photo22: Closeup of front end region with covers removed (1)
  • LAB photo23: Closeup of front end region with covers removed (2)
  • LAB photo24: Masahiro Morii installing FEA box
  • LAB photo25: David Coupal installing FEA box (1)
  • LAB photo26: David Coupal installing FEA box (2)

 

For comments, questions or changes to this page contact David MacFarlane mailb2.gif (2499 bytes)